About PME Laboratory

An independent lab for people who measure for a living.

Precision Measurement Engineering Laboratory was founded in Ras Al Khaimah in 2019 by engineers who were tired of waiting weeks for certificates that said little more than “pass”. We built the lab we wanted to send our own instruments to.

Our story

Calibration done properly, close to where you work.

The northern Emirates are home to oil and gas operators, manufacturers, utilities and telecom networks, all of which depend on test equipment that measures correctly. For years, much of that equipment had to travel to Dubai, Abu Dhabi or overseas to be calibrated, and spent weeks out of service.

We set up on Al Rams Road to change that: a laboratory with proper reference standards, a controlled environment and engineers who specialise in each discipline. Today we calibrate everything from handheld multimeters to microwave signal analyzers for clients across all seven Emirates.

  1. 2019

    Lab opens on Al Rams Road

    Founded in Ras Al Khaimah with electrical, DC/LF and time & frequency capability, anchored by a GNSS-disciplined reference.

  2. 2020

    Collection service across the UAE

    Contactless pick-up and return introduced, keeping clients’ instruments in calibration through lockdowns.

  3. 2021

    RF & microwave bench

    Spectrum analyzer, signal generator and RF power calibration added, extending capability to 26.5 GHz.

  4. 2022

    On-site calibration

    Portable standards and a dedicated on-site team for production floors and fixed installations.

  5. 2024

    Calibration management

    Instrument registers, monthly recall lists and certificate archives maintained on behalf of clients.

Principles

Three rules every engineer here works to.

01

Report what we measured

As-found data is always recorded, even when it is inconvenient. A certificate that hides a failure protects nobody.

02

State the uncertainty

Every result carries its expanded uncertainty. If a value is too close to a limit to call, we say so plainly.

03

Keep the promised date

Turnaround is quoted per instrument and tracked daily. If something will slip, you hear it from us first.

Quality & traceability

An unbroken chain back to the SI.

Traceability means every result can be linked, through a documented chain of calibrations each with stated uncertainty, to the international definition of the unit. Our quality system and procedures are built to the requirements of ISO/IEC 17025:2017, the international standard for testing and calibration laboratories.

  • Documented, validated calibration procedures
  • Uncertainty budgets per parameter, per range
  • Reference standards on a managed recall schedule
  • Internal audits and management reviews
  • Impartiality and confidentiality commitments
  1. Level 1

    SI units

    The International System of Units, realised by the BIPM and national metrology institutes.

  2. Level 2

    National & accredited labs

    Our primary references are calibrated by NMIs and ISO/IEC 17025-accredited laboratories.

  3. Level 3

    PME reference standards

    Multifunction calibrators, reference multimeters, power standards and a GNSS-disciplined rubidium clock.

  4. Level 4

    Working standards

    Checked against our references between external calibrations, with intermediate checks logged.

  5. Level 5

    Your instrument

    Calibrated against working standards, with the full chain identified on your certificate.

The laboratory

A controlled environment, monitored around the clock.

Precision measurements drift with temperature, humidity and supply noise. Our calibration area is held to tight limits and logged continuously, so environmental conditions are recorded on every certificate.

Temperature23.0 ± 1.0 °C
Relative humidity45 ± 10 %RH
ESD protectionGrounded benches & flooring
Mains supplyConditioned & UPS-backed
MonitoringContinuous, logged every 5 min
AcclimatisationMinimum 4 h before testing
The team

Specialists, not generalists.

Each discipline is owned by an engineer who maintains its standards, procedures and uncertainty budgets.

Laboratory Manager

Owns the quality system, technical review and certificate approval. Responsible for every result that leaves the lab.

Electrical & DC/LF Lead

Multimeters, calibrators, insulation and safety testers. Maintains our DC and low-frequency reference standards.

RF & Microwave Lead

Spectrum and signal analyzers, generators, power sensors and network analyzers up to 26.5 GHz.

Quality & Customer Coordinator

Your single point of contact for quotes, collections, recall reminders and audit documentation.

Visit us

On Al Rams Road, Ras Al Khaimah.

Drop off instruments during opening hours, or book a time to walk through the lab with one of our engineers. Parking is available directly outside.

Al Rams Road, Sector 1, Ras Al Khaimah, United Arab Emirates
Plan a visit
Opening hours
Monday – Friday08:00 – 18:00
Saturday09:00 – 14:00
SundayClosed

Collections and on-site work can be arranged outside these hours.

Start a calibration

Your next calibration is due sooner than you think.

Send us your instrument list and we will come back within one working day with a fixed quote, turnaround date and collection slot.